UB1000-18GM75 1 meter range Analog output water level Ultrasonic proximity sensor
Working Principle
The ultrasonic proximity switch's transmitter emits high-frequency ultrasonic waves. When these waves encounter an object, they are reflected back. The receiver captures the reflected echoes, and by measuring the time it takes for the ultrasonic waves to travel from transmission to reception, and combining this with the propagation speed of ultrasound in air, the distance between the sensor and the object can be calculated. When the distance reaches a preset threshold, the switch outputs the corresponding signal.
Product Features
1.M18 Installation
2.Multiple signal outputs
3.Non-contact detection
4.Strong environmental adaptability
5.Wide detection range
6.Unaffected by material
OUTPUT SELECTION GUIDE
1. Choose digital output (E4/E5):
When you only need to know "whether it has arrived": for example, whether a robotic arm has reached its position, whether a package is full, or whether a car door is closed.
Logic: Only two states, "on/off", respond the fastest, and cost the least.
2. Choose analog output (I/U):
When you need to know "how much distance": for example, to calculate the remaining height in a silo in real time, or the real-time distance between an AGV vehicle and obstacles.
Logic: Outputs continuously varying voltage/current, which the PLC can read as specific values for display or closed-loop control.
Product detail
Technical Specifications
|
Product model |
UB500-18GM75-E4-V15 |
UB1000-18GM75-E4-V15 |
UB500-18GM75-E6-V15 |
UB1000-18GM75-E6-V15 |
|
|
UB500-18GM75-E5-V15 |
UB1000-18GM75-E5-V15 |
UB500-18GM75-E7-V15 |
UB1000-18GM75-E7-V15 |
|
Detection range |
50...500mm |
70...1000mm |
50...500mm |
70...1000mm |
|
Detect dead zones |
0...50mm |
0...70mm |
0...50mm |
0...70mm |
|
Transducer frequency |
About 380khz |
About 205khz |
About 380khz |
About 205khz |
|
Response time |
About 50ms |
About 125ms |
About 50ms |
About 125ms |
|
Switching frequency |
≤8hz |
≤3hz |
≤8hz |
≤3hz |
|
Output type |
E4: NPN NO/NC |
E6: Two ways PNP NO/NC |
||
|
|
E5: PNP NO/NC |
E7: Two ways NPN NO/NC |
||
|
Rated operating current |
200mA short-circuit protection/overload protection |
2*100mA short-circuit protection/overload protection |
||
|
Operating voltage |
10-30VDC ripple 10% |
|||
|
Repeatability |
≤1% |
|||
|
Range adjustment |
The farthest and closest ranges are adjusted by the adjustment line |
|||
|
Degree of protection |
IP65 |
|||
|
Connection method |
V15 (5-pin) M12 cable/2m PVC cable |
|||
|
LED yellow light |
The switch status indicates that the yellow light flashes and the target is detected in the set state |
|||
|
LED red light |
Solid red: Error Flashing red light: No target detected in the set state |
|||
|
Product model |
UB500-18GM75-I-V15 |
UB1000-18GM75-I-V15 |
|
UB500-18GM75-U-V15 |
UB1000-18GM75-U-V15 |
|
|
Detection range |
50...500mm |
70...1000mm |
|
Detect dead zones |
0...50mm |
0...70mm |
|
Transducer frequency |
About 380KHZ |
About 205KHZ |
|
Response time |
About 50ms |
About 125ms |
|
Standard target board |
100mm*100mm |
|
|
Output type |
I: 4-20mA short circuit/overload protection |
|
|
U:0-10V |
||
|
Operating voltage |
I: 10-30VDC ripple 10% U: 15-30VDC ripple 10% |
|
|
No-load current |
I:≤45mA U:≤50mA |
|
|
Repeatability |
±1.5% of full-scale value |
|
|
Range adjustment |
The farthest and closest ranges are adjusted by the adjustment line |
|
|
Degree of protection |
IP65 |
|
|
Connection method |
V15 (5-pin) M12 cable/2m PVC cable |
|
|
LED yellow light |
The switch status indicator flashes The target has been detected in the set state |
|
|
LED red light |
Solid red light: Error Flashing red light: No target detected in the set state |
|