UB1000-T18 1000mm Ultrasonic distance sensor for Object recognition and material inspection
Working Principle
The ultrasonic proximity switch's transmitter emits high-frequency ultrasonic waves. When these waves encounter an object, they are reflected back. The receiver captures the reflected echoes, and by measuring the time it takes for the ultrasonic waves to travel from transmission to reception, and combining this with the propagation speed of ultrasound in air, the distance between the sensor and the object can be calculated. When the distance reaches a preset threshold, the switch outputs the corresponding signal.
Product Features
1.M18 Installation
2.Multiple signal outputs
3.Non-contact detection
4.Strong environmental adaptability
5.Wide detection range
6.Unaffected by material
APPLICATION scenario
1. Small-scale material/level monitoring: hoppers, small storage tanks, shallow troughs
2. Object in place/presence detection: assembly lines, assembly stations, mechanical positioning
3. Gap/thickness measurement: sheets, glass, films
4. Transparent object detection: PET bottles, glass, acrylic
5. AGV/cart collision prevention: short-distance obstacle warning
Product detail
Technical Specifications
|
Product model |
UB500-T18-E4-V15 |
UB1000-T18-E4-V15 |
UB500-T18-E6-V15 |
UB1000-T18-E6-V15 |
|
UB500-T18-E5-V15 |
UB1000-T18-E5-V15 |
UB500-T18-E7-V15 |
UB1000-T18-E7-V15 |
|
|
Detection range |
50...500mm |
70...1000mm |
50...500mm |
70...1000mm |
|
Detect dead zones |
0...50mm |
0...70mm |
0...50mm |
0...70mm |
|
Transducer frequency |
About 380khz |
About 205khz |
About 380khz |
About 205khz |
|
Response time |
About 50ms |
About 125ms |
About 50ms |
About 205ms |
|
Switching frequency |
≤8HZ |
≤3HZ |
≤8HZ |
≤3HZ |
|
Output type |
E4: NPN NO/NC |
E6：Two ways PNP NO/NC |
||
|
E5: PNP NO/NC |
E7：Two ways NPN NO/NC |
|||
|
Rated operating current |
200mA short-circuit protection/overload protection |
2*100mA short-circuit protection/overload protection |
||
|
Repeatability |
≤1% |
|||
|
Operating voltage |
10-30VDC ripple 10% |
|||
|
Range adjustment |
The farthest and closest ranges are adjusted by the adjustment line |
|||
|
Degree of protection |
IP65 |
|||
|
Connection method |
V15 (5-pin) M12 cable/2m PVC cable |
|||
|
LED yellow light |
The switch status indicates that the yellow light flashes and the target is detected in the set state |
|||
|
LED red light |
Solid red: Error Flashing red light: No target detected in the set state |
|||
|
Product number |
UB500-T18-I-V15 |
UB1000-T18-I-V15 |
|
UB500-T18-U-V15 |
UB1000-T18-U-V15 |
|
|
examination range |
50~500mm |
70~1000mm |
|
Detection blind zone |
0~50mm |
0~70mm |
|
Transducer frequency |
About 380khz |
About 205khz |
|
Response time |
About 50ms |
About 125ms |
|
Standard target board |
100*100mm |
|
|
Output type |
I: 4~20mA short circuit/overload protection |
|
|
U:0~10V |
||
|
Operating Voltage |
I:10~30VDC U:15~30VDC |
|
|
No-load current |
I:≤45Ma U:≤50mA |
|
|
Repeatability |
Full scale is worth ±1.5% |
|
|
Range adjustment |
Adjust the farthest and closest range by adjusting the line |
|
|
Protection level |
IP65 |
|
|
Connection method |
V15 (5 pin) M12 cable / 2 m PVC cable |
|
|
LED yellow light |
The switch status indicates that the yellow light is blinking. The target is detected in the set state. |
|
|
LED red light |
Steady red light: Error Red flashing: No target detected in the setting state |
|